Using Argus 2.3 under W7/32bit SP1. Kodi 15.0 front end - but that is probably irrelevant. Toshiba Satellite pro laptop, dual core, 2GHz, 4GB RAM, 250GB SSD.
Two USB tuners - PCTV 292e, and August DVB-T210. Both work, and both have latest drivers. 292e is top of card list in recorder console, T210 is second. Tuners are connected by an external powered USB hub.
Boot PC, and can record to either from the recorder console status page, and both appear to be doing EPG grabbing OK.
Put PC to sleep, and bring it back again. Now can only tune the 292e, the T210 says 'no signal'. The log shows:
I have tried different ordering for the cards, and all sorts of changes to the card timeout / tuning settings. Nothing makes any difference. Stopping and restarting services also have no effect.2015-10-05 08:08:51.5830 [Info ][Graph]: Started card service for card #2 'Digital TV'
2015-10-05 08:08:51.5830 [Info ][Heartbeat]: Heartbeat thread started.
2015-10-05 08:08:58.8058 [Info ][Graph]: Tuning to 4Music
2015-10-05 08:08:58.8994 [Debug][Graph]: Added BDA tuner for device Digital TV
2015-10-05 08:08:58.9306 [Debug][Graph]: Using filter AVStream TS Capture
2015-10-05 08:08:58.9462 [Debug][Graph]: Saved graph to C:\ProgramData\ARGUS TV\Graphs\Card-2.grf
2015-10-05 08:08:58.9618 [Debug][Graph]: Detected 2 signal statistics interfaces
2015-10-05 08:08:59.0086 [Info ][Graph]: Detected generic DvbT card
2015-10-05 08:08:59.0242 [Info ][Graph]: Tuning to 690000 8MHz Rate3_4 Mod64Qam
2015-10-05 08:08:59.0242 [Debug][Graph]: Starting graph
2015-10-05 08:09:04.2814 [Warn ][Graph]: Signal not locked!
2015-10-05 08:09:04.2814 [Debug][Graph]: Stopping graph
If I unplug the card and plug it in again, worse - the message changes to 'fatal' and the log shows:
The only thing that gets this card going again is a reboot. Then it is all fine - until put into standby again.2015-10-05 08:19:53.0408 [Info ][1]: Card host started for card #2.
2015-10-05 08:19:53.0564 [Info ][1]: Starting service host.
2015-10-05 08:19:54.3200 [Debug][Graph]: Using existing tuning space
2015-10-05 08:19:54.3200 [Info ][Graph]: Started card service for card #2 'Digital TV'
2015-10-05 08:19:54.3200 [Info ][Heartbeat]: Heartbeat thread started.
2015-10-05 08:19:54.4448 [Info ][Graph]: Tuning to 4Music
2015-10-05 08:19:54.4916 [Error][Graph]: Failed to build graph for @device:pnp:\\?\usb#vid_0572&pid_c688#7&1917a372&0&3#{71985f48-1ca1-11d3-9cc8-00c04f7971e0}\{972b7bb1-8149-4a72-b891-83e3c7dfe596}: System.Exception: Can't find a valid BDA tuner
at ArgusTV.Recorder.Graph.BdaGraphBase.AddAndConnectBDABoardFilters(String cardDevicePath)
at ArgusTV.Recorder.Graph.BdaGraphBase.EnsureGraph()
2015-10-05 08:19:54.5072 [Error][Graph]: StartRecording: System.Exception: Can't find a valid BDA tuner
at ArgusTV.Recorder.Graph.BdaGraphBase.AddAndConnectBDABoardFilters(String cardDevicePath)
at ArgusTV.Recorder.Graph.BdaGraphBase.EnsureGraph()
at ArgusTV.Recorder.Graph.BdaGraphBase.Tune(Satellite satellite, ITransponder transponder, ITuning tuning)
at ArgusTV.Recorder.Card.Cards.CardBase.TuneGraphTo(Satellite satellite, ITransponder transponder, ITuning tuning)
at ArgusTV.Recorder.Card.Cards.CardBase.TuneToService(Service service, Satellite satellite, ITuning& serviceTuning)
at ArgusTV.Recorder.Card.Cards.CardBase.StartStream[TCardStream](Service service, Satellite satellite, TsDemuxProcessorBase tsProcessor, Boolean skipDecoding, Boolean allowScrambled, TCardStream& cardStream)
2015-10-05 08:19:54.5394 [Info ][Graph]: Shutting down card service...
2015-10-05 08:19:54.5394 [Info ][Heartbeat]: Heartbeat thread ended.
2015-10-05 08:19:54.5394 [Info ][1]: Stopping service host.
2015-10-05 08:19:54.5394 [Info ][1]: Card host ended.
This makes it effectively unuseable for recordings, as the PC is always started from standby for commonsense reasons. Any suggestions?